Mod Menu Hack GameBreakingModern Ops v6.33 +15 UltimateModWallhack,Weapon DropHack,Radar,AimAssist. How to Set up BMW ICOM Next WiFi Connection? Run ITool Radar to detect ICOM information 2. Open IE browser and enter ICOM configuration address (based on current real ICOM IP ) 3. Select WLAN Settings Enter WiFi settings Save Changes. Disconnect LAN cable and restart ICOM, then ICOM will auto connect with WiFi. (, 04:06 AM) bmsmbs Wrote: I am wanting to connect my genuine ICOM to BMW Standard Tools software and I understand that I need to configure the connectivity setup using ITool Radar. I just installed ITool Radar on my 64bit Dell.

BMW ista-d ista-p Windows 7 install:

Step 1: ISTA-D Diagnosis software
Open software
Double click RHEINGOLD icon to change Full Screen
Go to Operations, then Read Out Vehicle Data, press Complete identification
Follow ISTA prompt to connect the ICOM emulator with vehicle
When it shows ICOM, you can click lower right corner Connect to start diagnosis. (If the Status shows firmware, you see update ICOM firmware first, see instruction in Part 5)

ITools Version 7 Help Manual Page 2 HA028838 Issue 5 Oct 10 2. RUNNING ITOOLS 2.1. LAUNCHING THE APPLICATION iTools may be launched in any of the following ways: 1. By starting the iTools application itself. The setup program creates a program group called 'Eu-rotherm iTools', containing an 'iTools' icon. Selecting this icon launches the. ITools is a cross-platform freeware that runs on Apple iOS, Mac, and Microsoft PC operating systems: Windows 7, 8, 8.1, 10, Vista, and XP. With iTools you can set your favorite songs as your ringtone, alter your GPS location, etc. The program is available in multiple languages: English, Chinese, German, Korean, Russian, Thai, and Vietnamese.

Step 2: ISTA-P Programming software
Open ISTA-P software
Click “Reset Settings” tab then close
Open it again
Select ISTA-P language and Resolution
Check the resolution on desktop, it is the same as ISTA-P resolution you just chose.
Select vehicle type, BMW, MINI, BMW Motorcycle or Rolls Royce
Select ISTA-P server automatically

Step 3: ETK
Open ETK software
Click “Extras” tab>> “Settings” to change language and other settings
KSD
Click “Settings” to change language and others

Step 4: Engineer Tools
Engineering & programming software INPA, NCS-Expert, WInKFP etc
Before using the engineer tools, must set/configure ICOM settings
1) Open Engineer Tools, Itool Radar, select first line option, click “Reserve” button on the right
ICOM Device status will be changed to Reserved.
2) Open EasyConnect, do following settings. The IP address must be set to correct 169.254.92.38, click “CHECK” button
Configuration is done. Start using engineering software (INPA, WinKFP, etc.)

Itool Radar Setup Software

BMW ista Windows 8.1 install:

Itool Radar Installation

Easy to do:
install Vredist 2013 and 2015, net framework 4.6.1 or 4.6.2
Install admin client and launcher
put license files in right location
Install all ISTA/P Files
Put all correct files in sharedstorage and install all.
Install standard tools , install patches
Use hardlink for PZData

BMW ista Windows 10 install:

Setup on Windows 10 64-bit:

After the Windows 10 update (which failed the first two attempts because it turned out the BIOS needed an update first) most applications were fine.

By simply revisiting the COM port settings for my K + DCAN USB to set back to COM9 , minimum buffer sizes and minimum latency Rheingold ran perfectly.

Loader V3.2 and ISTA-P was a bit more tricky. I re-ran the Network Config Tool. I tried Loader V4.3. No joy. However I did it nicely and ISTA-P runs nicely too, and with the excellent Loader V4.3 .

The Windows Networking and Networking Toolkit for Networking and Networking.

—> The setting was to go into Network Settings , select the USB Loopback which has been renamed ” Ethernet 2 ” and rename it to “USB” then go into its settings just like you would ENET lead and set the IPV4 IP to 169.254.0.8 with a mask of 255.255.0.0

Itool Radar Setup Software

Itool Radar Installation

Related posts: